Home > Uncategories > CCIE Collaboration Discussion

CCIE Collaboration Discussion

CCIE Collaboration Written & Lab Exam : Discussion & Sharing

All old posts will be archived automatically.
Sellers & Scammers no allowed.

  1. admin
    July 12, 2019 at 3:40 am

    We are here to share our Lab exam views, discussions and topics.
    This forum will help you to keep yourself updated for the exam preparations.

  2. ccasa
    July 26, 2019 at 3:17 am

    am trying to configure a Voice gateway AS5400 to route call from ISDN E1 to to a SIP server, I have configured the dial-peers , but when I try to make a call form , I hear noise like a modem voice I have been reading on Cisco website on this problem and they said all you need is to add the command “incoming called-number .” but still I am hearing the same noise

    ——————————————————————————–>

    ISDN E1———->AS5400 Voice Gateway ————–>SIP Server

    if you guys can take a look at it and see if I did something wrong.

    you help is highly appreciated

  3. tindo
    July 26, 2019 at 3:17 am

    I need to see configuration. eg. Sip-ua also if this GW setup as an IP2IPGW?

  4. Test
    July 26, 2019 at 3:18 am

    Also you have to make sure ISDN treats calls as a voice call

    Need to add under serial

    ISDN incoming-voice voice

    we need to see your config to help more

  5. anilkonge
    July 26, 2019 at 3:19 am

    Dear All,

    Can I use 7940 as a PSTN phone in my CCIE VOICE 3.0 Home Lab.

    Thanks in advance.

    Regards

  6. Test
    July 26, 2019 at 3:19 am

    NO you can’t use 7940 as PSTN phone. It has to register to the CUCM, which will assign it a DN.

    The best way to do a PSTN phone is to buy a $10 analog phone and plug it into a router. You can get any analog phone, try a thrift store. Check ebay and get yourself a MC3810 with a few FXS ports.You will need 1 FXS port per phone.

  7. See
    July 26, 2019 at 3:20 am

    Hello,

    I would not use a 7940, but you can.

    I have a 3640 (3x HD-2VEs + old CME) setup as my PSTN switch and use a 7960 for the PSTN phones.
    My reason for the 7960s is the additional line buttons.

    Hope that helps.

  8. see
    July 26, 2019 at 3:20 am

    I use a 3640 for my PSTN router (running old version of CME) with 2x NM-HD-2VEs (Cheap on ebay, if there is such a thing on the CCIE Voice track), then add the vwic-1mft-t1 or e1 as needed. Good news is that the 2VE has plenty of DSPs on it.

  9. bilash
    July 26, 2019 at 3:22 am

    I think better use the CIPC instead of 7940 as it has only 2 lines, or use 3×7940 is u have.

  10. nagen
    July 26, 2019 at 3:23 am

    What’s the major difference between NM-CUE and NM-CUE-EC ?

  11. fazalccie
    July 26, 2019 at 3:23 am

    NM-CUE-EC support more no of Concurrent users and mail boxes.As are using for Study purpose NM-CUE will be fine

  1. No trackbacks yet.

Leave a Reply

Your Details will Not be published